To the page content

22.11 - 02.12

cyberweek-deal

Millenium Rackstand 4U

109 Customer ratings

3.4 / 5

You have to be logged in to rate products.

Note: To prevent ratings from being based on hearsay, smattering or surreptitious advertising we only allow ratings from real users on our website, who have bought the equipment from us.

After logging in you will also find all items you can rate under rate products in the customer centre.

stability

quality

79 Reviews

Millenium Rackstand 4U
$9.30
The shipping costs are calculated on the checkout page.
In stock
In stock

This product is in stock and can be shipped immediately.

Standard Delivery Times
1
K
yeah, but no
Kristaps 28.10.2021
So it is supposed to be a 4 unit rack, but... On top there are this pole that holds it together, it is in a way of putting a 1st unit... But, i just got rid off the pole and it is holding together by the unit, so no problem there, unless you want to change units often. 2nd and 3rd unit, ok, BUT in 4th unit, that is in bottom, you can not putt anything that's deeper then few cm... So, not a full 4 unit stand, BUT, it is quite sturdy and really cheap... So basically, it is a 3 unit rack for few euros.
quality
stability
5
0
Report

Report

AF
A very badly designed product
Ashain Fernando 14.11.2020
Though the item is described to be a 4U unit, the maximum number of 1U units this can hold is only 2. Though is is very sturdy, the rack is very badly designed.
quality
stability
5
0
Report

Report

CM
Very poor design but usable for some things
Clavis Muziek 23.01.2023
I bought this to be able to put my 1U effects processor (Alesis Quadraverb GT) on the ground or next to me when I'm doing a show. It is impossible to insert large machine into this rack. You can only use it for small to medium sized depths. And I estimate no more than 2 or 3 units depending on the depth of your machines. Also a big negative point is the accuracy of the holes. Some of them just are little bit too narrow for the included screws. So be prepared to use a drill to adjust some of the holes a bit.
quality
stability
0
0
Report

Report

P
Not usable
Phonocat 04.02.2020
It's absolutely not usable. It can be used only for very not deep equipment, like level meter etc. Forget hooking up anything deeper than 12cm.
quality
stability
6
0
Report

Report

C
Sturdy, screw holes are not the standard size
CustomerA 26.07.2020
The rack feels sturdy and pretty well built. The only problem is that it only came with 8 screws and you need 16 to fill up the whole rack, so I bought some extra ones but they were too big! Why is this rack designed with non-standard holes? I bought the extra screws from Thomann so naturally, I assumed they'd fit.
quality
stability
2
0
Report

Report

i
Quality product-except screws, which are most important part
iDaga 19.02.2023
I had problems to screw gear into the rack, very bad screws and screwing on rack
quality
stability
0
0
Report

Report

O
not 4u
Oakidoki 05.06.2023
so as people may have read there is a bar at the top that you chuck in the bin right away so you can fit a unit in the top. i get a second unit under that and that will be it for full size units . the rack is built like a tank though just wish they had got the angle and design right
quality
stability
0
0
Report

Report

LE
Does what it's supposed to do
Lars Erhiff 13.09.2019
It's cheap, assembling it isn't slick, but it's cheap. Use it for a preamp in my home studio, and it works perfectly for that, I'd gladly buy another if I need to rack up more stuff like that.

If anybody looking at that picture believe they can take it on the road, Darwin can have 'em. But if you use it at home in a riskish free environment, feel free to procreate.
quality
stability
0
0
Report

Report

o
Pretty bad but suits my needs perfectly
olicarter 24.05.2019
So I bought this with the Adam Hall 4U Alu panel in an attempt to make my own Teensy-based synth.

I haven't put the top bar on as it gets in the way and wasn't needed for my use case. Though with the front panel screwed on, the large back horizontal bar simply doesn't fit. The design is truly terrible 😄

With that said... to build a lightweight desktop synth that doesn't extend very far back, it seems perfectly rock-solid and can see it lasting for ages! I wouldn't expect something deep (like my Focusrite 18i20 for example) to fit very well though.

You get what you pay for which may work for you, or not.
quality
stability
0
0
Report

Report

P
Build quality not up to par
PieterD 09.09.2024
The m5 screws don't fit. I needed to retread the wholes to remove the excess paint.
quality
stability
0
0
Report

Report

Millenium Rackstand 4U